Skip to content

Slope Calculator

Convert rise and run into slope percentage, angle, ratio and pitch.

I know the
Units
ft
ft
0

    Show the formula
    
      

    The plans called for a 3:1 fill slope, the storm drain spec demanded a 2 percent fall, and survey data arrived in degrees.

    Nobody was wrong. A 2 to 1 slope, 50 percent, and 26.6 degrees describe the same thing in different language, just as a 6 to 1 slope equals 16.7 percent, roughly 9.5 degrees on site.

    That is why the free converter exists. You work in whatever form the drawing hands you, enter percent, ratio, or degrees, and it calculates all three; you get the other two instantly, no tables needed.

    Rise over run, always: Percent Slope = (Rise ÷ Run) × 100. Feed it vertical rise and horizontal run, and it reports the slope percent, slope angle, decimal grade, slope ratio, and true surface length.

    For civil engineers, landscape architects, trail builders, or ADA compliance inspectors, the goal is turning raw field measurements into actionable gradient data for ramps, roads, roofs, stairs, drainage, terrain, with Imperial and metric both supported.

    How Do You Calculate Slope Percentage?

    Every ratio and every degree is merely translation, which is why drainage engineers writing paving specs always default to it.

    A percent grade multiplies that ratio by 100. When a road rises 3 feet over 100 feet, you have a 3% grade; a 1-foot rise over 100 feet gives a 1% grade, gentle yet functional.

    Calculate the slope percentage by dividing the total elevation gain (rise) by the total horizontal distance (run), then multiply that number by 100. Written in compact algebraic form, m = R/H and G = 100m.

    Picture a driveway 50 feet long whose end sits 4 feet higher than its beginning. Plug it in: 4′ / 50′ X 100 = 8% slope. Remember, Rise and run must use the same unit.

    Angles enter through the tangent function, comparing the opposite side of a right triangle to its adjacent side. So θ = tan⁻¹(Rise / Run) = tan⁻¹(Slope % / 100), meaning 5° works out near 8.75%.

    How Is Slope Represented?

    Because tan(45°) = 1, and 1 × 100% = 100%, that angle is a 100% slope, the point where rise matches run.

    Slope can be written in several forms, and each form is useful in a different context. In mathematics it is a decimal like 0.05; in construction, a percentage (**5%**); in geometry, an angle of 2.86°.

    Earthwork runs on the H:V ratio, horizontal to vertical. A 3H:1V slope means 3 feet of horizontal per 1 foot of vertical: 33.33%, about 18.43 degrees. A bigger first number always means a flatter slope.

    A 4:1 is gentle enough to mow and stabilize with grass. A 2:1 is steep, near the practical limit where fill holds without rip-rap or armoring; anything steeper, operators are not comfortable operating a dozer.

    Older plan sets use the V:H ratio, which flips the convention to vertical to horizontal, rise over run. The math is the same; only the reading order changes. Know which one your plans are using.

    How to Use the Slope Calculator

    1. Choose what you want to work out. Under I know the, pick Rise and run, Slope percentage or Angle. The boxes below change to match.
    2. Pick your units. Keep US for feet and inches, or switch to Metric for meters and centimeters. The default values change with it.
    3. Enter your measurements. Fill in the rise (height change), run (horizontal distance), slope and angle. You only see the boxes that apply to the option you picked.
    4. Read the result. The big number is your main answer. Below it you also see angle, pitch, drop per 100 ft, drop per foot and slope length. Open Show the formula to see every step with your numbers, or use Copy results to paste them into a message or shopping note.

    Worked Examples

    Start with the one people botch: a drainage pipe that drops 3 over 150. Set R = −3 and H = 150, then Slope % = −3/150 × 100% = −2%. The slope is −2%.

    A path rises 6 over 120. Work it as Slope % = 6/120 × 100%, then Slope % = 0.05 × 100% = 5%. The slope is 5%, meaning the path rises 5 per 100.

    A road sign shows an 8% grade. To get the angle, θ = tan⁻¹(8/100), so θ = tan⁻¹(0.08) ≈ 4.57°. An 8% slope is only about 4.57°, which surprises drivers who feel it braking downhill.

    A ramp built at an angle of 5° gives Slope % = tan(5°) × 100%, so Slope % ≈ 0.08749 × 100% = 8.75%. That 5° ramp is an 8.75% slope, already past ADA limits.

    When assessing a paved driveway that drops 15 feet over a 100-foot horizontal span, divide: 15 ÷ 100 = 0.15, then 0.15 × 100 = 15%. The driveway features a 15% slope, steep in winter.

    Where Is Slope Percentage Used?

    Math breaks before concrete does: the Zero Run Limitation. Horizontal run must be strictly greater than zero; a run of zero is a purely vertical drop and a mathematical division-by-zero error, leaving percent slope undefined.

    On audits, accessibility enforces ADA requirements for slope hardest: they require walkways not be steeper than 1:20, the cross slope not exceed 1:48, and Ramps cannot exceed 1:12, the 8.33% cap on standard wheelchair-accessible ramps.

    Only existing buildings get narrow exceptions: ramps between 1:12 and 1:10 allow a maximum rise less than 6″, while Ramps with slopes between 1:10 and 1:8 need a maximum rise less than 3″, nothing more.

    The 2018 International Plumbing Code wants horizontal drainage pipes at 1/4″ per foot (2%) minimum for 2 1/2″ or less, 1/8″ per foot for 3″ to 6″, and 1/16″ per foot for 8″ or larger.

    On grading plans, 2% crown is standard for most paved roads, shoulders run 4% to 6%, and a 6:1 foreslope equals 16.67%, about 9.46 degrees. Residential fill slopes are commonly specified at 3:1 or 4:1.

    Understanding Slope Percentage

    Does a 100% slope mean a vertical drop? No. 100% slope occurs exactly when the vertical rise perfectly equals the horizontal run, a base ratio of 1, at 45 degrees. A 90° slope is undefined.

    Run is not the sloped surface length, and the distinction matters: it is the horizontal distance measured along the ground or baseline. Measure along the sloped ramp instead, and the slope percentage will be incorrect.

    That sloped edge matters, just elsewhere.

    The Angle of Incline is the literal degree of the slope relative to a horizontal plane, via the inverse tangent function. Then come equivalent Radians, Per mille values, Gradient Ratio, and explicit Horizontal-to-Vertical (H:V) ratio.

    Gradient ratios rely on a uniform dimensional scale; if rise is measured in inches while run is recorded in feet, dividing them directly yields a mathematically invalid percentage. The tool must normalize the metrics first.

    Common Mistakes When Calculating Slope Percentage

    Slope percentage uses horizontal run, not the diagonal length, whether you measure a ramp, roof, hill, or road.

    Mixing units follows. Rise and run must use the same unit; do not divide 10 inches by 5 feet unless you convert one of them first, or a modest ramp suddenly reads twelve times steeper.

    Confusing angle and percentage: a 45° slope is 100%, not 45%; angle and percent grade are related by tangent, not direct equality. Forgetting to multiply by 100% matters: decimal slope 0.05 is 5%, not 0.05%.

    Ignoring direction trips up drainage or terrain work. A positive slope rises in the chosen direction; a negative slope falls. The sign depends on which direction you measure; state your reference before handing numbers over.

    Using zero run describes a vertical line: zero horizontal run means slope percentage is undefined, since division by zero is not allowed. Avoid assuming every slope requirement uses percent; always check which format is required.

    Common Slope Percentages and Angles

    Quick check before reading any chart: A 100% slope is 45°, not 90°. A 100% slope means the rise equals the run, which forms a 45° angle, and every gentler grade descends neatly from there.

    Down at the drainage end, 1% is 0.01 and 0.57°, or 1 in 100; 2% is 0.02, 1.15°, 1 in 50; and 3% reads 0.03, 1.72°, 1 in 33.33. Tiny angles, but very real consequences.

    Accessibility territory sits next: 5% equals 0.05, 2.86°, 1 in 20, while 8.33% is 0.0833, 4.76°, 1 in 12, the ramp ceiling. Push to 10% and you get 0.10, 5.71°, 1 in 10, noticeably steep.

    Driveways and earth banks live higher up. 12% is 0.12, 6.84°, 1 in 8.33; 20% is 0.20, 11.31°, 1 in 5; 25% is 0.25, 14.04°, 1 in 4; 50% reaches 0.50, 26.57°, 1 in 2.

    Rounded Decimal Grade and Slope % values drift, and drifting numbers become poured concrete.

    What This Calculator Does Not Do

    This slope math converter does the arithmetic and nothing beyond it.

    A 2:1 slope is 2:1 whether it is stable clay, loose fill, or the edge of a pond. The math is the same in all three cases, yet the engineering can vary widely between them.

    It will not size a culvert, choose a pipe diameter, or predict flow velocity. Those depend on discharge, roughness, and upstream catchment area, inputs that a geometric converter never sees and simply cannot reasonably guess.

    Nor does it account for compaction, settlement, frost heave, or groundwater. A grade staked perfectly today can shift within a season, which is why follow-up surveyed checks after rough grading still matter on serious projects.

    Treat the output as a translation, not a design approval. Always verify side slope specs with the project engineer before grading, and keep local code requirements, permits, and geotechnical recommendations in front of every number.

    Frequently Asked Questions

    How Do You Calculate Slope Percentage?

    Always start with the rise, measuring vertical change first, then the horizontal distance. Divide one by the other, multiply by 100, and you have a percent grade. Skip a step and steepness misleads you.

    What Does A 5% Slope Mean?

    Think of a 5% slope as a gentle angle, about 2.86°, where every 100 units of horizontal run brings 5 units of rise. Its decimal grade is 0.05, a 1:20 ratio most walkers barely notice.

    Is Slope Percentage The Same As Slope Angle?

    People confuse the two constantly. A 45° angle is 100% slope, not 45%, because slope percentage compares rise to run, while angle is measured in degrees from the horizontal. Related by tan(θ), yet genuinely different.

    How Do You Convert Slope Percent To Angle?

    Use the arctangent whenever a site crew gives you a percentage but needs degrees. Take an 8% slope example: tan⁻¹(0.08) lands ≈ 4.57°, so θ = that angle, which feels surprisingly shallow in actual practice.

    How Do You Convert Angle To Slope Percentage?

    Ramps built at a 5° pitch show how small angles hide large ratios. Run tan(5°), which gives 0.08749, then apply × 100%: Slope % lands ≈ 8.75%, so every ramp deserves a proper second check.

    What Is A 1:12 Slope As A Percentage?

    Accessibility inspectors know the ADA maximum ramp slope by heart: 1:12. That means 1 unit of rise per 12 units of run, or 1/12 × 100% ≈ 8.33%. Steeper fails inspection and frustrates wheelchair users.

    Can Slope Percentage Be Negative?

    Yes, and the sign tells the whole story. Negative slope percentage means the surface falls in your travel direction; −2% is a drop of 2 per 100. Reverse your walk and the sign flips instantly.

    What Happens If Run Is Zero?

    Picture a vertical line: it has zero horizontal run, so the percentage slope is undefined because division by zero is not allowed. No calculator, however clever, can rescue that situation, so check your run first.