Skip to content

Gutter Calculator

Get a complete gutter shopping list from your eave length and number of runs.

Units
ft
Each run has its own two ends.
ft
Ground to gutter, for downspout length.
in
24 in is standard. Use 18 in in heavy snow areas.
0

    5 in K-style gutters suit most homes. Large or steep roofs and heavy-rain areas often need 6 in gutters.

    Show the formula
    
      

    To buy gutters, you need the total eave length and the number of separate gutter runs. Everything else follows from those two numbers: 10 ft sections, downspouts, hangers, end caps, elbows and downspout pipe. With the calculator's defaults (120 ft of eave in 2 runs, a 10 ft eave height and hangers every 24 in), you need 120 ft of gutter. That is 12 sections of 10 ft, with 4 downspouts, 60 hangers, 4 end caps, 12 elbows and 40 ft of downspout pipe.

    How to Use the Gutter Calculator

    1. Pick your units. Keep US for feet and inches, or switch to Metric.
    2. Enter the total eave length. Add together every roof edge that will get a gutter.
    3. Enter the number of separate gutter runs. A run is a continuous length of gutter with two ends. A plain rectangular ranch house with gutters on the front and back has 2 runs. Each run gets two end caps and at least one downspout.
    4. Enter the inside and outside corners. An outside corner wraps around the outside of the house. An inside corner sits where two roof edges meet in an L.
    5. Enter the eave height. This is the distance from the ground to the gutter. It sets the length of downspout pipe.
    6. Set the hanger spacing. 24 in is standard. Use 18 in in heavy snow areas or under a large roof.
    7. Read the result. The big number is the total length of gutter. Below it you see the 10 ft gutter sections, downspouts, downspout pipe, elbows, hangers, end caps, outlets (drops) and corners. Show the formula explains each count.

    How the Gutter Parts Are Counted

    PartRule usedDefault example
    GutterTotal eave length120 ft
    10 ft sectionsEave length ÷ 10, rounded up12
    DownspoutsThe larger of: one per run, or one per 35 ft of gutter4
    Downspout pipeDownspouts × eave height40 ft (4 × 10 ft pieces)
    Elbows3 per downspout (two at the eave, one at the bottom)12
    Outlets (drops)1 per downspout4
    HangersEave length in inches ÷ hanger spacing, rounded up60
    End caps2 per run4
    CornersAs entered0 / 0

    Buy a few extra hangers and screws, a tube or two of gutter sealant, and pop rivets for sectional gutters. If your downspouts run away from the house, add extensions or splash blocks too.

    How to Measure for Gutters

    1. Measure each eave along the fascia board where the gutter will hang. Measuring on the ground directly under the eave is fine for a one-story house.
    2. Note where each run starts and stops. A run stops at a corner unless you plan to wrap the corner with a miter.
    3. Pick the downspout locations: at corners, near the ends of runs, and where the water can drain away from the foundation, not onto a walkway or driveway.
    4. Measure the eave height at each downspout location. Use the tallest one in the calculator to be safe.

    Gutter Size: 5 Inch or 6 Inch?

    5 in K-style gutters suit most homes. 6 in gutters are a better choice for large or steep roofs, for roofs where an upper slope drains onto a lower one, and for places with heavy rain. They carry much more water, and they usually pair with larger 3 × 4 in downspouts instead of 2 × 3 in. See our guide to gutter sizes for a fuller comparison.

    Installing Gutters: Key Measurements

    • Slope: pitch the gutter toward each downspout, commonly about ¼ in of drop for every 10 ft. On long runs, slope from the middle down to a downspout at each end.
    • Hanger spacing: every 24 in, or every 18 in in snow country. Drive the hanger screws into the fascia and, where you can, into the rafter tails behind it.
    • Position: set the back of the gutter under the drip edge so water off the roof lands in the gutter, not behind it.
    • Downspout discharge: carry the water at least a few feet away from the foundation.

    Planning to hire the job out? The gutter cost calculator estimates the installed price for vinyl, aluminum, steel or copper.

    Frequently Asked Questions

    How do I calculate how much gutter I need?

    Measure the length of every roof edge that will have a gutter and add them together. Divide by 10 and round up to get the number of 10 ft sections. For seamless gutters, the installer works from your total length.

    How many downspouts do I need?

    Plan on one downspout for every 30 to 40 ft of gutter, and at least one per separate run. The calculator uses one per 35 ft or one per run, whichever is more. Heavy-rain areas and large roofs benefit from more.

    How far apart should gutter hangers be?

    Every 24 in is standard. In areas with heavy snow and ice, space them every 18 in so the gutter does not sag or pull away.

    How much slope should a gutter have?

    A common target is about ¼ in of fall for every 10 ft of gutter toward the downspout. Too little slope leaves standing water, and too much looks crooked from the street.

    How many elbows do I need per downspout?

    Usually three: two at the top to bring the downspout back from the gutter outlet to the wall, and one at the bottom to turn water away from the house. Downspouts that jog around trim or windows need more.

    Should I use seamless or sectional gutters?

    Seamless gutters have fewer joints and fewer leaks, but they are formed on site by a contractor. Sectional gutters come in 10 ft pieces that you can install yourself. If you go sectional, plan for a joint or connector between sections and seal each one well.